Store
4 images in this album.
[Slideshow] [Login]
Strawberry decals red-01.  45 year commemorative decals designed by Kelley R. Dodd (www.krdpdx.com) and manufactured by Gary Prange (www.sssink.com).  These dry-fix decals are for professional application and must be clear coated for durability.  $25 postpaid.  To order, please contact Andy. PayPal and good check accepted.  Why the name Strawberry?  Sort of a long story.  In 1970 after graduating from engineering school, I lived in the Cotswolds near Bulls Cross, Stroud, a few miles from Gloucester.  Once a week I rode in a  massed start road race in the Bristol area and during one of the train trips down to Bristol I learned of a road race across the English/Scottish border held the week before the Commonwealth Games in Edinburgh.  This sounded like an adventure, so I headed north on the train with my new Bob Jackson bicycle.  The road race included national team members and it was no sooner apparent that I was out of my depth than I was desperately off the back of the pack touring the highlands of Scotland.  A week later the weather was still abysmal but the scenery cycling down Loch Ness was beautiful.  Returning south, I spent a few days in London and ordered a Hetchins cycle frame for a girlfriend.  My interest in cycle frame construction was piqued by the Hetchins shop visit.  Fast forward, I returned to Portland and thought to attempt to fabricate cycle frames, but under what moniker?    My father, Lawrence Fraser Newlands, Scottish on both sides, suggested the Fraser crest.  Research into the Fraser name in Scotland shows Norman roots from the mid - 12th. century and that it is derived from the French word fraise, meaning Strawberry.  However, the origin of the name Fraser is disputed, and indeed, the name may be a pun on the strawberry flowers on the Fraser heraldic crest.  All in good humor, the name "Strawberry Bicycle" was trademarked in 1971.  The new version decals shown above include the Fraser moto: Je suis prest (I am ready).  It was decided to not include the war cry.  The Frasers were actually kind of a bloody minded lot in the old days.
Strawberry decals red-01. 45 year commemorative decals designed by Kelley R. Dodd (www.krdpdx.com) and manufactured by Gary Prange (www.sssink.com). These dry-fix decals are for professional application and must be clear coated for durability. $25 postpaid. To order, please contact Andy. PayPal and good check accepted. Why the name Strawberry? Sort of a long story. In 1970 after graduating from engineering school, I lived in the Cotswolds near Bulls Cross, Stroud, a few miles from Gloucester. Once a week I rode in a massed start road race in the Bristol area and during one of the train trips down to Bristol I learned of a road race across the English/Scottish border held the week before the Commonwealth Games in Edinburgh. This sounded like an adventure, so I headed north on the train with my new Bob Jackson bicycle. The road race included national team members and it was no sooner apparent that I was out of my depth than I was desperately off the back of the pack touring the highlands of Scotland. A week later the weather was still abysmal but the scenery cycling down Loch Ness was beautiful. Returning south, I spent a few days in London and ordered a Hetchins cycle frame for a girlfriend. My interest in cycle frame construction was piqued by the Hetchins shop visit. Fast forward, I returned to Portland and thought to attempt to fabricate cycle frames, but under what moniker? My father, Lawrence Fraser Newlands, Scottish on both sides, suggested the Fraser crest. Research into the Fraser name in Scotland shows Norman roots from the mid - 12th. century and that it is derived from the French word fraise, meaning Strawberry. However, the origin of the name Fraser is disputed, and indeed, the name may be a pun on the strawberry flowers on the Fraser heraldic crest. All in good humor, the name "Strawberry Bicycle" was trademarked in 1971. The new version decals shown above include the Fraser moto: Je suis prest (I am ready). It was decided to not include the war cry. The Frasers were actually kind of a bloody minded lot in the old days.
Viewed: 11338 times.
Strawberry decals white-02.  45 year commemorative decals designed by Kelley R. Dodd (www.krdpdx.com) and manufactured by Gary Prange (www.sssink.com).  These dry-fix decals are for professional application and must be clear coated for durability.  $25 postpaid.   To order, please contact Andy. PayPal and good check accepted.
Strawberry decals white-02. 45 year commemorative decals designed by Kelley R. Dodd (www.krdpdx.com) and manufactured by Gary Prange (www.sssink.com). These dry-fix decals are for professional application and must be clear coated for durability. $25 postpaid. To order, please contact Andy. PayPal and good check accepted.
Viewed: 9814 times.
Strawberry 45 year commemorative brass belt buckle designed by my wife, Kelley Dodd (www.krdpdx.com) and manufactured in the USA.  $35.00 delivered via USPS throughout the lower 48.  To order, please contact Andy. PayPal and good check accepted.  Buckle is designed for Western belts up to 1-3/4" wide and is cast in solid brass and measures approximately 3-3/4" x 2-1/4".
Strawberry 45 year commemorative brass belt buckle designed by my wife, Kelley Dodd (www.krdpdx.com) and manufactured in the USA. $35.00 delivered via USPS throughout the lower 48. To order, please contact Andy. PayPal and good check accepted. Buckle is designed for Western belts up to 1-3/4" wide and is cast in solid brass and measures approximately 3-3/4" x 2-1/4".
Viewed: 10282 times.
Strawberry stock "Sport" 700c and "Rambler" 650b road framesets are offered here for cyclists looking to purchase a fine handbuilt frameset (frame + fork + headset). The frames are hand brass brazed in Reynolds 631 or 853 Air Hardening steel tubing. Why brass brazing? Reynolds 631 pre-brazed strength is in the range of 800-900 MPa (116,100 psi - 130,600 psi) and 853 is in the range of 1200-1400 MPa ( 174,120 - 203,140psi) and the after brazed strength is significantly higher. Quoting Reynolds " The strength to weight ratio of the air hardening steels is equal to that of quality titanium and aluminum frames. A normal chrome molybdenum steel will lose strength in the joints after the heat has been applied. This material (631 and 853) INCREASES in strength when heated to around 850 degrees C (1560 degrees F), (note: 850 degrees is the BRASS BRAZING temperature - silver brazing does not achieve this increase in strength) and the recommended braze metal is used per AWS Classification, RBCuZn type. As the frame cools the tubing increases in strength to well in excess of the as delivered values shown above. This unique air hardening property of Reynolds 631 and 853 provides additional stiffness through reduced micro-yielding at the joints, allowing stiffer frames with excellent fatigue strength when compared to standard chrome molybdenum and excellent ride quality to be constructed." An Enve road carbon fork is matched to the 700c frame (650b frames have a steel fork with the Strawberry designed double plate style fork crown) and is sold assembled with a 1-1/8" headset. The frames are fabricated with Marchetti fixtures in the Strawberry Workshop (shop pics may be viewed by clicking on the Mechanique link), Portland, Oregon by Andy Newlands who has over forty five years experience in the cycles engineering and fabrication field. Materials include the finest investment cast bottom bracket (English threading), lugs, dropouts, Strawberry designed wishbone rear triangle with the new LAN71 Integrated Seatpost Binder, and full compliment of braze-on's. Cost is $2500 for Reynolds 631 and $2600 for Reynolds 853 tubing,Ex Works, Goose Hollow, Portland, OR, or $2600 for a 631 frameset or $2700 for a 853 frameset delivered via UPS Ground throughout the lower 48 states.  Sorry, no international shipping.   As the framesets are completed they will be available for viewing at the Strawberry workshop and also posted here on the Strawberry website.
Strawberry stock "Sport" 700c and "Rambler" 650b road framesets are offered here for cyclists looking to purchase a fine handbuilt frameset (frame + fork + headset). The frames are hand brass brazed in Reynolds 631 or 853 Air Hardening steel tubing. Why brass brazing? Reynolds 631 pre-brazed strength is in the range of 800-900 MPa (116,100 psi - 130,600 psi) and 853 is in the range of 1200-1400 MPa ( 174,120 - 203,140psi) and the after brazed strength is significantly higher. Quoting Reynolds " The strength to weight ratio of the air hardening steels is equal to that of quality titanium and aluminum frames. A normal chrome molybdenum steel will lose strength in the joints after the heat has been applied. This material (631 and 853) INCREASES in strength when heated to around 850 degrees C (1560 degrees F), (note: 850 degrees is the BRASS BRAZING temperature - silver brazing does not achieve this increase in strength) and the recommended braze metal is used per AWS Classification, RBCuZn type. As the frame cools the tubing increases in strength to well in excess of the as delivered values shown above. This unique air hardening property of Reynolds 631 and 853 provides additional stiffness through reduced micro-yielding at the joints, allowing stiffer frames with excellent fatigue strength when compared to standard chrome molybdenum and excellent ride quality to be constructed." An Enve road carbon fork is matched to the 700c frame (650b frames have a steel fork with the Strawberry designed double plate style fork crown) and is sold assembled with a 1-1/8" headset. The frames are fabricated with Marchetti fixtures in the Strawberry Workshop (shop pics may be viewed by clicking on the Mechanique link), Portland, Oregon by Andy Newlands who has over forty five years experience in the cycles engineering and fabrication field. Materials include the finest investment cast bottom bracket (English threading), lugs, dropouts, Strawberry designed wishbone rear triangle with the new LAN71 Integrated Seatpost Binder, and full compliment of braze-on's. Cost is $2500 for Reynolds 631 and $2600 for Reynolds 853 tubing,Ex Works, Goose Hollow, Portland, OR, or $2600 for a 631 frameset or $2700 for a 853 frameset delivered via UPS Ground throughout the lower 48 states. Sorry, no international shipping. As the framesets are completed they will be available for viewing at the Strawberry workshop and also posted here on the Strawberry website.
Viewed: 15015 times.
Powered by Gallery v1 [RSS]